XYZprinting Da Vinci 2.0

alaTest har samlet og analyseret 7 anmeldelser fra magasiner og hjemmesider. Folk kan virkelig godt lide udskriftskvaliteten. Også præstationen imponerer, men folk er mindre positive med hensyn til kvaliteten.

pris, præstation, udskriftskvalitet

pålidelighed, størrelse, kvalitet

Gennemsnitligt vurderede brugere dette produkt til 63/100.

Anmeldelsesanalyse

(Baseret på 7 anmeldelser)

Brugeranmeldelser  

Anmdeldelsesratings

  (29% af anmeldelser)
Viser alle 5 stjernede anmeldelser   (29% af anmeldelser)
Viser alle 4 stjernede anmeldelser   (ingen anmeldelser)
    (14% af anmeldelser)
Viser alle 2 stjernede anmeldelser   (29% af anmeldelser)
Viser alle 1 stjernede anmeldelser

Funktioner

brugervenlighed
  Vis positive (50%)Vis negative (50%)(Vis alle)
pris
  Vis positive (91%)Vis negative (9%)(Vis alle)
pålidelighed
  Endnu ingenVis negative (100%)(Vis alle)
størrelse
  Endnu ingenVis negative (100%)(Vis alle)
præstation
  Vis positive (100%)Endnu ingen(Vis alle)
design
  Vis positive (50%)Vis negative (50%)(Vis alle)
udskriftskvalitet
  Vis positive (100%)Endnu ingen(Vis alle)
kvalitet
  Endnu ingenVis negative (100%)(Vis alle)
Vis flere funktioner

Viser 7 anmeldelse(r)

Ekspertanmeldelser Brugeranmeldelser

Disclaimer:

Herunder er en liste over anmeldelser for dette eller lignende produkter. Hvis du tror, denne gruppering er forkert klik her for at flag.
Læs mere på vores FAQ side.
Viser 1 - 7 af 7 Vis anmeldelser: på Dansk | på andre sprog

Brugeranmeldelse (newegg.com)

Not bad for the price

 

Price is at the lower end for the type of printing quality you get ; Print quality is pretty good compared to others at the price range ; Easy to calibrate once you know what your doing ; Loading the filament is easy and pain free even for noobs If you...

Tray needs calibrating often because of metal warping with heat constantly changing and when removing part from the tray if it's stuck to the try it take a bit of force to remove even if you don't use the glue stick. Unless you use software that uses a...

Jul 2015
Læs hele anmeldelsen

Brugeranmeldelse (newegg.com)

Waste of your time & money

 

Run, don't walk. Look further cause this anchor isn't worth it.

Price alone

keeps breaking down. Arrived inoperative. Needed new display board, Heater failures are recurring. Replaced two heaters already. Broken belt already. More down time than up. Absolutely NO help from XYZ. I'm converting mine to an Arduino controller to...

Apr 2015
Læs hele anmeldelsen

Brugeranmeldelse (newegg.com)

Great buget printer

 

Like all 3D printers there's no such things as plug and play even though they might try to market them as so. Be prepared to spend the time to learn about and maintain the printer. Also when buying a 3D printer do your research on what they can and can...

It's a very good price for a dual extruder printer. The print quality is pretty good out box too. I like the cartridge system as well since it keeps things nice an tidy and keeps track of how much filament is left. The software actually slices pretty...

The calibration can be a pain since the heated bed rests on top of a plastic frame. It susceptible to expansion and contraction which leads to different calibration number each time. The metal contacts used to calibrate can also get dirty fairly easily...

Feb 2015
Læs hele anmeldelsen

Brugeranmeldelse (newegg.com)

Good quality price product

 

Easy, works with Autodesk product, low cost, entry level printer

Need conversion of files and adjustments, its not all automatic like a standard printer. Require some doing to print

Feb 2015
Læs hele anmeldelsen

Brugeranmeldelse (newegg.com)

Disappointed

 

If I had it to do over again I would have purchased the DaVinci 1.0, saved $150 and had a great deal more mods and work arounds availabe and a larger print bed. It's probably a cheap way to get started with 3D printing but don't expect very good results.

The plug&play aspect is a nice feature and the overall package is attractive. The unit seems to be well engineered for quick factory assembly

The proprietary filament cartridge is a limitation but there are work arounds available ; The two color option seemed like a neat feature but on most of the things I have tried there is a considerable of filament mixing since the extruder apparently...

Nov 2014
Læs hele anmeldelsen

Brugeranmeldelse (newegg.com)

Great!!!!

 

If i had to buy another one and would go for the single extruder model just cuz i have not found any reason to use both extruders in one print!

Works great! For the price you cannot beat HAve used high dollar ones before and dont see why you wouldnt just go with the lower priced printer cuz they produce the same product

You have to calibrate it every once in a while but once it has been done once it gets really easy

Nov 2014
Læs hele anmeldelsen

Brugeranmeldelse (newegg.com)

bad printer

 

none

defective printer. couldn't even print a built in test object

Okt 2014
Læs hele anmeldelsen

Prissammenligning for XYZprinting Da Vinci 2.0

Ingen priser på dette produkt